Free Share Lead2pass Cisco 300-180 VCE Dumps With New Update Exam Questions:
https://www.lead2pass.com/300-180.html
QUESTION 81
For a KVM session to be successful, which two of these need to be done? (Choose two.)
A. The Cisco IMC IP address needs to be assigned on the Admin tab.
B. The Cisco IMC IP address needs to be in the same subnet as the management IP.
C. The Cisco IMC needs to be upgraded to the same version as the UCS Manager.
D. The server needs to be fully discovered.
Answer: AD s
QUESTION 82s
A customer is configuring SAN pin groups in a Cisco UCS domain.
The customer notices that pinning is not working and traffic from the vHBA is not passing over the Fibre Channel uplink port. Which of these must be done for pinning to work correctly?
A. Include the SAN pin group in a vHBA policy and then include the vHBA policy in the service profile
that is assigned to that server.
B. Include the SAN policy in the Cisco UCS Manager to match with pin groups on the fabric interconnect.
C. The customer must have Cisco UCS Manager version 2.0 or above.
D. Fibre Channel switch mode needs to be configured first.
Answer: A
QUESTION 83
Refer to exhibit. A Cisco UCS admin is troubleshooting an issue with a vNIC not coming up on a blade. When looking at the CLI of the “Fabric Interconnect”,the admin runs this command to view the status of the interface.
Which option describes a possible reason why the interface is stuck in an “initializing” state?
A. The service profile is not applied to a blade.
B. The VLANs defined on the vNIC are not defined on a matching uplink port.
C. The uplink port is down.
D. The QoS policy on the vNIC is invalid.
E. The MTU on the vNIC is higher than the MTU configured in the QoS system class.
Answer: C
QUESTION 84
Which two options are causes for failure of a Cisco C-Series server that is configured to boot from SAN? (Choose two.)
A. The boot LUN ID is not 0.
B. The ISCSI target is only available via one via one path through the network.
C. C-Series does not support boot from SAN.
D. The KVM dongle is attached to the front of the server with a USB stick installed.
E. Under the FCoE properties on the vNIC adapter, the FCoE VLAN ID is set to 10.
F. The boot table for fc0 has not been configured.
Answer: DF
QUESTION 85
Which command on the Fabric Interconnect displays packet statistics for a given QoS group and MTU size?
A. show policy-map interface ethernet x/y
B. show queuing interface ethernet x/y
C. show interface ethernet x/y
D. show class-map type qos
E. show interface queuing ethernet x/y
Answer: B
QUESTION 86
A Cisco UCS admin is trying to integrate Cisco UCS Manager with Active Directory Authentication. After the configuration is done, the admin is still unable to log in using LDAP credentials. When running a debug on the Fabric Interconnect, this error is displayed:
ldap_build_roles_and_locales_from_attr: No attr for usr profile
Which step was missed in the configuration?
A. The LDAP provider was not configured correctly.
B. The proper RBAC role(s) were not assigned to the user.
C. Cisco UCS Manager 2.1 is required for LDAP integration.
D. The “Attribute” field in Cisco UCS was left blank.
Answer: B
QUESTION 87
Which three requirements are needed to configure a blade to boot successfully from Fibre Channel? (Choose three.)
A. zoning
B. LUN masking
C. WWPN device alias
D. boot from SAN policy
E. SAN connectivity policy
F. port assignment
G. target WWPN needs to be set in the boot from SAN policy
Answer: ABD
QUESTION 88
Which description of a core file is true?
A. It is generated by a system failure.
B. It is generated by a process failure.
C. It is generated by a component failure.
D. It is generated by a hardware failure.
Answer: B
QUESTION 89
Which logs are used to troubleshoot hardware failure?
A. system event log
B. audit log
C. accounting log
D. gateway logs
E. system log
Answer: A
QUESTION 90
A UCS Admin is trying to launch the KVM console but it is failing to launch. All IP Pools for mgmt are configured and the CIMC has an address in UCSM. They SSH to the fabric Interconnect and run an ethanalyzer while issuing a ping from their local PC to the KVM IP address. The ping is successful but they do not see the ICMP requests and replies displayed in the capture. Here is the filter they used:
FIA(nxos)# ethanalyzer local interface mgmt display-filter icmp limit-captured-frames 0
What could be the reason pings are not seen in the capture and the KVM is failing to load?
A. Java settings are preventing the KVM from loading
B. There is a duplicate IP address for that CIMC address
C. The switch upstream from the FI has the wrong vlan configured
D. The CIMC IP pool is in the same subnet as the Fabric Interconnects mgmt 0 interface
Answer: B
300-180 dumps full version (PDF&VCE): https://www.lead2pass.com/300-180.html
Large amount of free 300-180 exam questions on Google Drive: https://drive.google.com/open?id=108Bd0NBc2wWwiFC-bUg8eLE5zS0n9gVN
You may also need:
300-165 exam dumps: https://drive.google.com/open?id=0B3Syig5i8gpDSkhBVngxX0Z3Y0k
300-170 exam dumps: https://drive.google.com/open?id=0B3Syig5i8gpDdHhmcTBIbGM4bmc
300-175 exam dumps: https://drive.google.com/open?id=0B3Syig5i8gpDVDYyRldqb1AzenM